Contact: +48 511 131 594
Contact:
info@imex-company.com
info@imex-company.com
IMEX COMPANY
Everything that the military needs!
4 MAJOR INGURY PREVENTION
TRANSITION FROM "STATE 300" TO "STATE 200"
COMPRESSION INJURIES OF THE SPINE: PROTRUSIONS AND HERNIATIONS
LOSS OF LEGS/FEET AS A RESULT OF AN ANTI-PERSONNEL MINE EXPLOSION
SHRAPNEL DAMAGE
Problem:
Large blood losses in case of injury, lung damage, respiratory failure lead to a significant decrease in the level of saturation (the amount of oxygen in the blood), which, in turn, leads to loss of consciousness or even life. Hypoxia causes irreversible processes in the brain, which are later recognized as non-combat losses. This often occurs in the yellow zone and during the transportation of casualties to hospitals. Timely oxygen therapy is one of the priorities of modern aid.
Oxygen in cylinders at the front line is dangerous because a bullet or shrapnel hits the cylinder causing an explosion and death or serious injury to military medics.
Solution:
Provide tactical medics and evacuation vehicles with sources of safe oxygen produced in the United States, -
SAROS tactical oxygen concentrators. The model 3000 allows safe production of oxygen 24/7 from a battery
and/or power supply network.
The concentrator has the form of
of a 10-liter oxygen cylinder. It is maintenance-free and self-regenerating.
Large blood losses in case of injury, lung damage, respiratory failure lead to a significant decrease in the level of saturation (the amount of oxygen in the blood), which, in turn, leads to loss of consciousness or even life. Hypoxia causes irreversible processes in the brain, which are later recognized as non-combat losses. This often occurs in the yellow zone and during the transportation of casualties to hospitals. Timely oxygen therapy is one of the priorities of modern aid.
Oxygen in cylinders at the front line is dangerous because a bullet or shrapnel hits the cylinder causing an explosion and death or serious injury to military medics.
Solution:
Provide tactical medics and evacuation vehicles with sources of safe oxygen produced in the United States, -
SAROS tactical oxygen concentrators. The model 3000 allows safe production of oxygen 24/7 from a battery
and/or power supply network.
The concentrator has the form of
of a 10-liter oxygen cylinder. It is maintenance-free and self-regenerating.
Problem:
When an equipped soldier gets out of an armored vehicle, jumps from a tank, over a window sill or actively moves between trenches, the additional load on the spine reaches its maximum impact: given the weight of the equipment up Taking into account the weight of equipment up to 20-30 kg (weapons, BК, body armor), the load on the SPINE increases 9.8 times in dynamics, up to almost 200 kg.
This causes protrusions and hernias of the spine, which, in turn, makes it impossible to restore the soldier's health quickly and conservatively and return him to service or to normal social life.
Solution:
Israel scientists have developed an anti-gravity belt system (patented T-belt) that allows you to relieve the load from the shoulder girdle and spine, and prevent the above-mentioned problem. The result of using such a vest by the IDF has resulted in a reduction in spinal injuries of the spine and increased endurance of military personnel, which is extremely important for working "at ground zero" and behind enemy lines.
When an equipped soldier gets out of an armored vehicle, jumps from a tank, over a window sill or actively moves between trenches, the additional load on the spine reaches its maximum impact: given the weight of the equipment up Taking into account the weight of equipment up to 20-30 kg (weapons, BК, body armor), the load on the SPINE increases 9.8 times in dynamics, up to almost 200 kg.
This causes protrusions and hernias of the spine, which, in turn, makes it impossible to restore the soldier's health quickly and conservatively and return him to service or to normal social life.
Solution:
Israel scientists have developed an anti-gravity belt system (patented T-belt) that allows you to relieve the load from the shoulder girdle and spine, and prevent the above-mentioned problem. The result of using such a vest by the IDF has resulted in a reduction in spinal injuries of the spine and increased endurance of military personnel, which is extremely important for working "at ground zero" and behind enemy lines.
Problem:
Loss of limbs and pelvic organs as a result of an anti-personnel mine explosion is a frequent result of advancing through enemy territory and during counteroffensive operations. Then there are amputations of the limb or its part with subsequent prosthetics. The loss of blood in such injuries can be life-threatening. It is impossible to restore the soldier and return to duty, and the quality of civilian life is significantly deteriorating.
Solution:
The use of mine-resistant boots developed by Israel scientists, instead of conventional boots, can withstand an explosion equivalent to 50 grams of TNT, which covers the entire spectrum of high-explosive anti-personnel mines in the world. This destroys the sole of the boot, but the foot and limb are preserved. Special insoles absorb the energy of an explosion.
Loss of limbs and pelvic organs as a result of an anti-personnel mine explosion is a frequent result of advancing through enemy territory and during counteroffensive operations. Then there are amputations of the limb or its part with subsequent prosthetics. The loss of blood in such injuries can be life-threatening. It is impossible to restore the soldier and return to duty, and the quality of civilian life is significantly deteriorating.
Solution:
The use of mine-resistant boots developed by Israel scientists, instead of conventional boots, can withstand an explosion equivalent to 50 grams of TNT, which covers the entire spectrum of high-explosive anti-personnel mines in the world. This destroys the sole of the boot, but the foot and limb are preserved. Special insoles absorb the energy of an explosion.
Problem:
Even when wearing high-quality body armor and mine-resistant shoes, the legs, knees, elbows, groin, and arms are vulnerable to shrapnel. Wearing a conventional military uniform does not protect these parts of the body, while leaving full mobility of the limbs and not overloading the weight of various neck, shoulder or groin pads. The use of a sapper suit is not possible when a soldier is actively moving. So the problem lies in the openness to injury to these parts of the body. Moreover, small shrapnel in the
the legs, groin or arms is problematic to remove - it requires
long-term surgical interventions with blood loss.
Solution:
Israel scientists have developed an unprecedented military
uniforms (pants, long underpants and a shirt under the body armor) for
IDF soldiers that can hold shrapnel fragments by itself
weighing up to 1.1 grams at speeds of up to 260 m/s. This allows to
protect the legs (the groin and thighs are additionally protected by long
legs, knees, elbows, and neck from minor
but dangerous injuries. The uniform is fireproof and washable.
The set weighs no more than 1.5 kg (pants, underwear and shirt).
Even when wearing high-quality body armor and mine-resistant shoes, the legs, knees, elbows, groin, and arms are vulnerable to shrapnel. Wearing a conventional military uniform does not protect these parts of the body, while leaving full mobility of the limbs and not overloading the weight of various neck, shoulder or groin pads. The use of a sapper suit is not possible when a soldier is actively moving. So the problem lies in the openness to injury to these parts of the body. Moreover, small shrapnel in the
the legs, groin or arms is problematic to remove - it requires
long-term surgical interventions with blood loss.
Solution:
Israel scientists have developed an unprecedented military
uniforms (pants, long underpants and a shirt under the body armor) for
IDF soldiers that can hold shrapnel fragments by itself
weighing up to 1.1 grams at speeds of up to 260 m/s. This allows to
protect the legs (the groin and thighs are additionally protected by long
legs, knees, elbows, and neck from minor
but dangerous injuries. The uniform is fireproof and washable.
The set weighs no more than 1.5 kg (pants, underwear and shirt).
Problem:
Large blood losses in case of injury, lung damage, respiratory failure lead to a significant decrease in the level of saturation (the amount of oxygen in the blood), which, in turn, leads to loss of consciousness or even life. Hypoxia causes irreversible processes in the brain, which are later recognized as non-combat losses. This often occurs in the yellow zone and during the transportation of casualties to hospitals. Timely oxygen therapy is one of the priorities of modern aid.
Oxygen in cylinders at the front line is dangerous because a bullet or shrapnel hits the cylinder causing an explosion and death or serious injury to military medics.
Solution:
Provide tactical medics and evacuation vehicles with
sources of safe oxygen produced in the United States, -
SAROS tactical oxygen concentrators. The model
3000 allows safe production of oxygen 24/7 from a battery
and/or power supply network. The concentrator has the form of
of a 10-liter oxygen cylinder. It is maintenance-free and self-regenerating.
Large blood losses in case of injury, lung damage, respiratory failure lead to a significant decrease in the level of saturation (the amount of oxygen in the blood), which, in turn, leads to loss of consciousness or even life. Hypoxia causes irreversible processes in the brain, which are later recognized as non-combat losses. This often occurs in the yellow zone and during the transportation of casualties to hospitals. Timely oxygen therapy is one of the priorities of modern aid.
Oxygen in cylinders at the front line is dangerous because a bullet or shrapnel hits the cylinder causing an explosion and death or serious injury to military medics.
Solution:
Provide tactical medics and evacuation vehicles with
sources of safe oxygen produced in the United States, -
SAROS tactical oxygen concentrators. The model
3000 allows safe production of oxygen 24/7 from a battery
and/or power supply network. The concentrator has the form of
of a 10-liter oxygen cylinder. It is maintenance-free and self-regenerating.
Problem:
When an equipped soldier gets out of an armored vehicle, jumps from a tank, over a window sill or actively moves between trenches, the additional load on the spine reaches its maximum impact: given the weight of the equipment up Taking into account the weight of equipment up to 20-30 kg (weapons, BК, body armor), the load on the SPINE increases 9.8 times in dynamics, up to almost 200 kg.
This causes protrusions and hernias of the spine, which, in turn, makes it impossible to restore the soldier's health quickly and conservatively and return him to service or to normal social life.
Solution:
Israel scientists have developed an anti-gravity belt system (patented T-belt) that allows you to relieve the load from the shoulder girdle and spine, and prevent the above-mentioned problem. The result of using such a vest by the IDF has resulted in a reduction in spinal injuries of the spine and increased endurance of military personnel, which is extremely important for working "at ground zero" and behind enemy lines.
When an equipped soldier gets out of an armored vehicle, jumps from a tank, over a window sill or actively moves between trenches, the additional load on the spine reaches its maximum impact: given the weight of the equipment up Taking into account the weight of equipment up to 20-30 kg (weapons, BК, body armor), the load on the SPINE increases 9.8 times in dynamics, up to almost 200 kg.
This causes protrusions and hernias of the spine, which, in turn, makes it impossible to restore the soldier's health quickly and conservatively and return him to service or to normal social life.
Solution:
Israel scientists have developed an anti-gravity belt system (patented T-belt) that allows you to relieve the load from the shoulder girdle and spine, and prevent the above-mentioned problem. The result of using such a vest by the IDF has resulted in a reduction in spinal injuries of the spine and increased endurance of military personnel, which is extremely important for working "at ground zero" and behind enemy lines.
Problem:
Loss of limbs and pelvic organs as a result of an anti-personnel mine explosion is a frequent result of advancing through enemy territory and during counteroffensive operations. Then there are amputations of the limb or its part with subsequent prosthetics. The loss of blood in such injuries can be life-threatening. It is impossible to restore the soldier and return to duty, and the quality of civilian life is significantly deteriorating.
Solution:
The use of mine-resistant boots developed by Israel scientists, instead of conventional boots, can withstand an explosion equivalent to 50 grams of TNT, which covers the entire spectrum of high-explosive anti-personnel mines in the world. This destroys the sole of the boot, but the foot and limb are preserved. Special insoles absorb the energy of an explosion.
Loss of limbs and pelvic organs as a result of an anti-personnel mine explosion is a frequent result of advancing through enemy territory and during counteroffensive operations. Then there are amputations of the limb or its part with subsequent prosthetics. The loss of blood in such injuries can be life-threatening. It is impossible to restore the soldier and return to duty, and the quality of civilian life is significantly deteriorating.
Solution:
The use of mine-resistant boots developed by Israel scientists, instead of conventional boots, can withstand an explosion equivalent to 50 grams of TNT, which covers the entire spectrum of high-explosive anti-personnel mines in the world. This destroys the sole of the boot, but the foot and limb are preserved. Special insoles absorb the energy of an explosion.
The problem:
Even when wearing high-quality body armor and mine-resistant shoes, the legs, knees, elbows, groin, and arms are vulnerable to shrapnel. Wearing a conventional military uniform does not protect these parts of the body, while leaving full mobility of the limbs and not overloading the weight of various neck, shoulder or groin pads. The use of a sapper suit is not possible when a soldier is actively moving. So the problem lies in the openness to injury to these parts of the body. Moreover, small shrapnel in the
the legs, groin or arms is problematic to remove - it requires long-term surgical interventions with blood loss.
Solution:
Israel scientists have developed an unprecedented military uniforms (pants, long underpants and a shirt under the body armor) for IDF soldiers that can hold shrapnel fragments by itself weighing up to 1.1 grams at speeds of up to 260 m/s.
This allows to protect the legs (the groin and thighs are additionally protected by long legs, knees, elbows, and neck from minor but dangerous injuries.
The uniform is fireproof and washable.
The set weighs no more than 1.5 kg (pants, underwear and shirt).
Even when wearing high-quality body armor and mine-resistant shoes, the legs, knees, elbows, groin, and arms are vulnerable to shrapnel. Wearing a conventional military uniform does not protect these parts of the body, while leaving full mobility of the limbs and not overloading the weight of various neck, shoulder or groin pads. The use of a sapper suit is not possible when a soldier is actively moving. So the problem lies in the openness to injury to these parts of the body. Moreover, small shrapnel in the
the legs, groin or arms is problematic to remove - it requires long-term surgical interventions with blood loss.
Solution:
Israel scientists have developed an unprecedented military uniforms (pants, long underpants and a shirt under the body armor) for IDF soldiers that can hold shrapnel fragments by itself weighing up to 1.1 grams at speeds of up to 260 m/s.
This allows to protect the legs (the groin and thighs are additionally protected by long legs, knees, elbows, and neck from minor but dangerous injuries.
The uniform is fireproof and washable.
The set weighs no more than 1.5 kg (pants, underwear and shirt).
Oxygen for the battlefield SAROS
Oxygen for the battlefield SAROS
Oxygen saturation of the blood is extremely important for life, therefore it is important to maintain a high level of oxygen in the blood of the wounded in case of lung damage or large blood loss. Using an oxygen cylinder on the battlefield is extremely risky, as a bullet or debris entering the cylinder causes an explosion and injury or death to military medics. However, the use of oxygen, starting from the "yellow zone" on the battlefield, increases the time of providing effective medical care to the wounded, and this leads to a reduction of non-combat losses by 5 times.
The SAROS 3000 oxygen concentrator is safely used directly on the battlefield and during the evacuation phase.
The SAROS 3000 oxygen concentrator is safely used directly on the battlefield and during the evacuation phase.
Medical parameters:
The equivalent of oxygen therapy is 15 l/min
Oxygen is dosed as a medicine in mg
Continuously produces oxygen 24/7 (220V, 24V or replaceable battery)
Autonomy works with a replaceable battery for 90 minutes
The device detects breathing and adjusts the oxygen supply - when breathing stops, it turns on the maximum ventilation mode
Physical parameters:
- The SAROS oxygen concentrator has the dimensions of a 10-liter oxygen cylinder and easily replaces it;
- Certified for Black Hawk helicopters and HMMWV vehicles (Maximum operating altitude is 5500m above sea level)
- Dust, vibration and moisture resistant
Since 2008, the US Army has replaced more than 7,000 oxygen tanks to concentrators SAROS.
Oxygen therapy is part of the NATO protocols for providing medical aid to the wounded
Allows to reduce non-combat losses (evacuation stage) by 5 times and provides additional time for a medic to provide medical service.
Oxygen therapy is part of the NATO protocols for providing medical aid to the wounded
Allows to reduce non-combat losses (evacuation stage) by 5 times and provides additional time for a medic to provide medical service.
Oxygen for bomb shelters
Oxygen for bomb shelters
During military operations, the population is faced with the need to stay in bomb shelters regularly. Among such people there are people who need special care, because rocket fire is a huge stress. Against the background of stress, conditions of chronic diseases worsen, especially in the elderly.
People with heart and lung diseases are at risk. Emergency situations may also occur.
Equipping the bomb shelter with oxygen equipment - oxygen concentrators or stations allows providing medical assistance to such people. As you know, oxygen is an indispensable medicine for diseases of the human cardiovascular and respiratory system. The ability to provide oxygen therapy or help in time saves lives.
We offer oxygen equipment - Ukrainian-made oxygen stations and USA-made oxygen concentrators for equipping bomb shelters in schools, hospitals, subways and municipal facilities.
Reduces the risk of death from heart attack, exacerbation of cardiovascular and breathing complications, COVID infections
People with heart and lung diseases are at risk. Emergency situations may also occur.
Equipping the bomb shelter with oxygen equipment - oxygen concentrators or stations allows providing medical assistance to such people. As you know, oxygen is an indispensable medicine for diseases of the human cardiovascular and respiratory system. The ability to provide oxygen therapy or help in time saves lives.
We offer oxygen equipment - Ukrainian-made oxygen stations and USA-made oxygen concentrators for equipping bomb shelters in schools, hospitals, subways and municipal facilities.
Reduces the risk of death from heart attack, exacerbation of cardiovascular and breathing complications, COVID infections
Anti-splinter form
Combined with ergonomic body armor and anti-mine footwear, the ACCS military uniform provides an unprecedented level of military protection. The innovative design and materials, from each the ACCS military uniform made, provide enhanced protection against ballistic threats, fire and other hazards in aggressive environments.
- Antimicrobial properties
- Fireproof: does not melt
- Anti-mosquito protection
- Ballistic protection
- Super strong
- Composite textile with ceramic inserts in the exposed knee/elbow area
- Ballistic felt lining for protection against shrapnel
- Light, elastic and breathable torso fabric
- Elastic fabric inserts for comfort and fit
- 6 mesh ventilation holes
- Protective knee pads and elbow pads
- Sleeve compression regulator
- Ballistic neck protection
- Low-profile interior zip pocket
- Wrist straps
- Waist adjustment
- Internal and external pockets
- Cargo pocket with elastic band and front and top access
- Quick access ankle pocket
Natural, lightweight and very durable FR DuraLastTM fabric has physical properties 50% better than NYCO fabrics currently used in combat clothing. Natural FR DuraLastDotTM fabric (used for elbow and knee pockets) is 25% more abrasion resistant than Cordura 500D.
ACCS is fire resistant (does not melt, drip) according to EN ISO 11612:2015 (Procedures A1, A2, B1, C1 & F1).
FR VaporDriftTM natural stretch fabric used in the torso area provides excellent sweat wicking and heat dissipation when the body armor is worn. Patented zippered ventilation pockets promote airflow and body heat control, and provide the GATI system with the same or better thermal management performance compared to non-ballistic combat clothing available on the market.
Patent-pending integrated ultra-light ProPadsTM knee and elbow pads are load-distributing, puncture-resistant and impact-resistant to EN 14404, and provide additional ballistic protection for the wearer's knees and elbows.
NoSnagTM clothing design is attractive and highly functional. Light, protective, with good moisture wicking fabric with an excellent touch to the skin.
DyneemaKnitTM natural stretch fabric built into the garment protects the wearer's SHOULDER and PELVIS from low-velocity fragments.
A DyneemaFeltTM insert built into the collar protects the wearer's NECK from low-speed flying debris.
The 3DShieldTM layer built into the knee and elbow pads protects the wearer's KNEE and ELBOW from low-speed flying fragments.
The form withstands debris type F1-F5 (weighing up to 1.1 grams)
The test was carried out according to the methodology: STANAG 2920 Ed.3 / AEP 2920 Ed A V2
A DyneemaFeltTM insert built into the collar protects the wearer's NECK from low-speed flying debris.
The 3DShieldTM layer built into the knee and elbow pads protects the wearer's KNEE and ELBOW from low-speed flying fragments.
The form withstands debris type F1-F5 (weighing up to 1.1 grams)
The test was carried out according to the methodology: STANAG 2920 Ed.3 / AEP 2920 Ed A V2
The user is at the center of everything a manufacturer does. The design and development processes involve the input of experts and users at every opportunity to identify, track and resolve human-related issues. ACCS field trials conducted in Israel and the United Kingdom measured the systems' performance in cold and hot weather and high heat loads against current UK Army regular uniforms.
The trials were conducted in collaboration with a leading academic institute using state-of-the-art sensors, technology and methodology to collect data that measures ACCS performance in terms of comfort, usability, size and fit, functionality, warrior agility and integration with weapons and vehicles. Evaluation of user feedback and technical data from the trials shows that ACCS scores significantly higher in almost all respects than the current UK Army uniform.
The Company's ACCS ProPads were also evaluated during trials, including an agility/assault course involving crawling
and moving through restrictive obstacles.
100% of the soldiers surveyed said they preferred the built-in elbow pad in the UBACS. ProPads were tested on various types of hard ground (concrete, stone) and sharp objects.
100% of the soldiers surveyed stated that the ProPads are comfortable, easy to adjust and stay in place during use.
The ACCS design and fabric specifications were determined by special operations veterans who were tasked with defining the "world's best combat uniform."
Since there were no fabrics on the market that met these specifications, the company had to develop new fabrics to meet
the requirements. ACCS's basic fabrics are flame and melt resistant, extremely durable, have improved evaporation, heat transfer and ventilation properties, are protected from bacteria and fungal infections, and have increased mechanical strength. New ballistic protective fabrics have been developed to provide innovative ballistic protection in high vulnerability areas.
Since there were no fabrics on the market that met these specifications, the company had to develop new fabrics to meet
the requirements. ACCS's basic fabrics are flame and melt resistant, extremely durable, have improved evaporation, heat transfer and ventilation properties, are protected from bacteria and fungal infections, and have increased mechanical strength. New ballistic protective fabrics have been developed to provide innovative ballistic protection in high vulnerability areas.
A shirt under the body armor
The shirt under the body armor is a part of ACCS, the world's most advanced system of combat clothing,
developed by IDF special forces specialists. The shirt provides improved protection against the negative effects of the environment and ballistic protection without compromising comfort and ease of use.
developed by IDF special forces specialists. The shirt provides improved protection against the negative effects of the environment and ballistic protection without compromising comfort and ease of use.
The shirt provides improved protection against the negative effects of the environment and ballistic protection without compromising comfort and ease of use. The tactical shirt includes a unique protection - ArmoFelt ballistic felt for delaying ballistic fragments, built into the neck and shoulder area.
All ballistic elements provide effective protection against fragments, while minimizing the effect on heat exchange (heat transfer and sweating). Patented ultra-light elbow pads integrated into the sleeves provide impact and ballistic protection. The ballistic protection collar can be worn high or folded down if full coverage is not required.
Zip vents improve airflow and ventilation to better control of body heat.
Shirt pockets, adjustment straps and zippers are designed so that they do not catch on external objects - as flat as possible to the surface of the garment. All pockets are closed with zippers or Velcro, as well as loops for attaching equipment. The torso area is made of FlexDrift fabric. This new, revolutionary fabric is flexible, breathable, as well as soft and stretchy. The elongated body design of the shirt ensures that the shirt stays tucked in even during
extreme movements. The sleeves and shoulders are made from the new DuraYarn fabric and textile, which provides high strength combined with breathability.
DuraDot fabric is used in the elbow pockets to improve user protection and grip during crawling and general work.
4 zippered vents increase airflow and ventilation to better control body heat.
All ballistic elements provide effective protection against fragments, while minimizing the effect on heat exchange (heat transfer and sweating). Patented ultra-light elbow pads integrated into the sleeves provide impact and ballistic protection. The ballistic protection collar can be worn high or folded down if full coverage is not required.
Zip vents improve airflow and ventilation to better control of body heat.
Shirt pockets, adjustment straps and zippers are designed so that they do not catch on external objects - as flat as possible to the surface of the garment. All pockets are closed with zippers or Velcro, as well as loops for attaching equipment. The torso area is made of FlexDrift fabric. This new, revolutionary fabric is flexible, breathable, as well as soft and stretchy. The elongated body design of the shirt ensures that the shirt stays tucked in even during
extreme movements. The sleeves and shoulders are made from the new DuraYarn fabric and textile, which provides high strength combined with breathability.
DuraDot fabric is used in the elbow pockets to improve user protection and grip during crawling and general work.
4 zippered vents increase airflow and ventilation to better control body heat.
Based on an anthropometric study of UK army personnel, the manufacturer's team has developed an advanced sizing methodology that covers 95% of users with only 10 shirt sizes.
To find your shirt size, you need to take 2 measurements with the help of an assistant with a standard measuring tape. The chest measurement determines the shirt size. The torso height measurement determines the shirt and sleeve length.
GENERAL MEASUREMENT PROCEDURE:
Posture:
Standing or sitting upright, depending on the measurement. Arms are relaxed.
Measure during a normal breath.
Method:
Conducted with an assistant.
Remove shirts (including T-shirts) and belts, leave underwear on. Measure with a measuring tape.
Repeat each measurement. If you have a noticeable difference between the first and second measurement,
repeat until you have two accurate consecutive measurements.
TORSO HEIGHT (ABOVE OR BELOW 38.5 CM)
With the subject sitting upright, the assistant lightly applies the tape to the top
of the sternum and measures to the top of the navel (women should measure
between the bust)
CHEST CIRCUMFERENCE
With the subject standing upright, the assistant measures the circumference at nipple level around the chest (women should measure around the fullest part of the chest). Make sure the tape is flat (parallel to the ground) around the subject.
Tighten the tape only enough to maintain contact between the tape and the skin.
To find your shirt size, you need to take 2 measurements with the help of an assistant with a standard measuring tape. The chest measurement determines the shirt size. The torso height measurement determines the shirt and sleeve length.
GENERAL MEASUREMENT PROCEDURE:
Posture:
Standing or sitting upright, depending on the measurement. Arms are relaxed.
Measure during a normal breath.
Method:
Conducted with an assistant.
Remove shirts (including T-shirts) and belts, leave underwear on. Measure with a measuring tape.
Repeat each measurement. If you have a noticeable difference between the first and second measurement,
repeat until you have two accurate consecutive measurements.
TORSO HEIGHT (ABOVE OR BELOW 38.5 CM)
With the subject sitting upright, the assistant lightly applies the tape to the top
of the sternum and measures to the top of the navel (women should measure
between the bust)
CHEST CIRCUMFERENCE
With the subject standing upright, the assistant measures the circumference at nipple level around the chest (women should measure around the fullest part of the chest). Make sure the tape is flat (parallel to the ground) around the subject.
Tighten the tape only enough to maintain contact between the tape and the skin.
Tactical pants
Tactical pants are part of ACCS, the world's most advanced system of combat clothing, developed by IDF special forces specialists. The pants provide improved protection
against the negative effects of the environment and ballistic protection without
compromising comfort and ease of use. The main fabric does not burn, does not melt,
does not drip, is light, but very strong, designed for 6 months of use.
Patented ventilation system to facilitate airflow and manage body heat.
Internal Knee ProPadsTM pockets with an adjustment mechanism to align the pad
with the user's knee. Unique design of NoSnagTM side pockets that expand inward,
eliminating the danger of snagging. All features are glove compatible.
The high-friction thigh area is seamless to avoid skin chafing.
against the negative effects of the environment and ballistic protection without
compromising comfort and ease of use. The main fabric does not burn, does not melt,
does not drip, is light, but very strong, designed for 6 months of use.
Patented ventilation system to facilitate airflow and manage body heat.
Internal Knee ProPadsTM pockets with an adjustment mechanism to align the pad
with the user's knee. Unique design of NoSnagTM side pockets that expand inward,
eliminating the danger of snagging. All features are glove compatible.
The high-friction thigh area is seamless to avoid skin chafing.
- Innovative combination of THREE new fabrics in the pants - FR DuraLastTM,
- FR DuraLastDotTM & FR CareLaStrechTM. Developed by the GATI team
- from fiber to fully functional fabric - lightweight, durable, breathable and protective.
- Side adjustment tabs – Help adjust the pants to the user's waist.
- Belt loops - designed to attach the C BELTTM (supplied as a separate part
- of the ACC system) or any other belt.
- Double-sided elastic fabric FR CareLaStrechTM - for areas of clothing
- where necessary bending/extending the body.
- Top side pockets - for essentials such as a mobile phone and
- a multi-tool.
- Spacious NoSnagTM Side Pockets - With top and side access, the pocket turns
- inward to avoid snagging. Elastic band inside the pocket for attaching equipment.
- Patented zippered ventilation pockets – for airflow in the groin area.
- Side Zippered Kneepad Pocket - designed for use with patent pending ProPadsTM kneepads (sold separately).
- The pocket is made of FR DuraLastDotTM fabric, which is more durable than CorduraTM. Internal vertical
- adjustment mechanism to position the knee pad in line with the user's knee, side fastening to keep the knee pad firmly in place during maneuvers.
- Side ankle pocket - can be used while sitting in the car.
- Leg cuff closures - elastic cord with a trash retainer and insect protection around the top of the boot.
- Seamless zone to avoid chafing in high friction thigh area - no seams to avoid chafing the skin.
- Two-layer zone of areas with a high level of friction - to extend the service life of the pants.
It's the little things that matter - pocket drainage holes, reliable loops for equipment, zippers that can be used in gloves.
Based on an anthropometric study of UK Army personnel, the team developed an improved sizing methodology that covers 95% of the user population with only 10 pant sizes.
To find a pant size, you need to take 2 measurements with the help of an assistant with a standard measuring tape. The waist
circumference determines the size of the pants. The inside leg height measurement will determine the pant length.
GENERAL MEASUREMENT PROCEDURE:
Posture:
- Standing upright.
- Arms are relaxed.
- Measure during a normal breath
Method:
- Conducted with an assistant.
- Take off your shirts (including T-shirts) and belts, leave your underwear on.
Measure with a measuring tape.
- Repeat each measurement. If you have a noticeable difference between the first and second
measurement, repeat until you have two accurate consecutive measurements.
INTERNAL LEG LENGTH
The subject holds a straight object, such as a pencil, and marks the level of his or her groin. The subject should stand upright with the heel of the pencil on the measuring tape marked 10 cm above ground level.
The assistant will measure the distance between ground level and the straight line marking the groin level and then subtract 10 cm from the measurement.
WAIST CIRCUMFERENCE
With the subject standing upright, the assistant should locate the top of the pelvic bones. Measure 3 cm (approximately 2 fingers below the pelvic bone) on each side to determine the reference points. The subject should point to the two reference points with their thumbs at a
90-degree angle to the body. The assistant measures directly below the reference points across the body and parallel to the ground. Tension the tape only enough to maintain contact between the tape and the skin.
To find a pant size, you need to take 2 measurements with the help of an assistant with a standard measuring tape. The waist
circumference determines the size of the pants. The inside leg height measurement will determine the pant length.
GENERAL MEASUREMENT PROCEDURE:
Posture:
- Standing upright.
- Arms are relaxed.
- Measure during a normal breath
Method:
- Conducted with an assistant.
- Take off your shirts (including T-shirts) and belts, leave your underwear on.
Measure with a measuring tape.
- Repeat each measurement. If you have a noticeable difference between the first and second
measurement, repeat until you have two accurate consecutive measurements.
INTERNAL LEG LENGTH
The subject holds a straight object, such as a pencil, and marks the level of his or her groin. The subject should stand upright with the heel of the pencil on the measuring tape marked 10 cm above ground level.
The assistant will measure the distance between ground level and the straight line marking the groin level and then subtract 10 cm from the measurement.
WAIST CIRCUMFERENCE
With the subject standing upright, the assistant should locate the top of the pelvic bones. Measure 3 cm (approximately 2 fingers below the pelvic bone) on each side to determine the reference points. The subject should point to the two reference points with their thumbs at a
90-degree angle to the body. The assistant measures directly below the reference points across the body and parallel to the ground. Tension the tape only enough to maintain contact between the tape and the skin.
Tactical ballistic underwear
Advanced Combat Clothing System (ACCS)
Ballistic underwear is part of the Advanced Combat Clothing System (ACCS).
ACCS, developed by IDF Special Forces, is the most advanced combat clothing system in the world.
Ballistic underwear is part of the Advanced Combat Clothing System (ACCS).
ACCS, developed by IDF Special Forces, is the most advanced combat clothing system in the world.
Ballistic underwear is a part of the advanced system (ACCS). ACCS, developed
by specialists of the IDF special unit, is the most modern system of combat clothing
in the world. Provides unique built-in protection against ballistic fragments for highly vulnerable areas of the torso and pelvis. The system's innovative fabrics are designed, certified and tested to be durable yet lightweight, breathable and optimized for heat transfer. The advanced methodology of determining the sizes of combat clothing
ensures a perfect fit, comfort and the correct location of all protective elements.
The underwear has an ergonomic design (models available for both men and women) to ensure a comfortable fit, free movement and urination without removing the underwear. The ballistic layer is made of innovative Guardian Armor – a light, soft and breathable ballistic material. Guardian consists of the world's strongest Dyneema® fiber combined with other high-quality fibers in a patented process that provides 360o ballistic protection against shrapnel, and also is breathable, two-way stretch fabric, hydrophilic and anti-bacterial for coolness, softness and comfort in contact with skin.
by specialists of the IDF special unit, is the most modern system of combat clothing
in the world. Provides unique built-in protection against ballistic fragments for highly vulnerable areas of the torso and pelvis. The system's innovative fabrics are designed, certified and tested to be durable yet lightweight, breathable and optimized for heat transfer. The advanced methodology of determining the sizes of combat clothing
ensures a perfect fit, comfort and the correct location of all protective elements.
The underwear has an ergonomic design (models available for both men and women) to ensure a comfortable fit, free movement and urination without removing the underwear. The ballistic layer is made of innovative Guardian Armor – a light, soft and breathable ballistic material. Guardian consists of the world's strongest Dyneema® fiber combined with other high-quality fibers in a patented process that provides 360o ballistic protection against shrapnel, and also is breathable, two-way stretch fabric, hydrophilic and anti-bacterial for coolness, softness and comfort in contact with skin.
- Vertical/horizontal fly - allows you to pass urine without lowering the pants. Women's model designed for use in the she-wee style (female urinal).
- Lightweight compression sports cut - for maximum comfort and free blood circulation.
- Ballistic protection - ballistic protection pieces for the pelvis and upper thighs, protected by 360 degrees Guardian Armor fabric.
- Five different sizes for a comfortable fit.
- The orange label makes it easy to check if troops are following the command's instructions to prepare the garment before deployment.
Technical properties - Guardian ballistic underwear fabric
ProPads elbow pads with ACCS shirt
ProPads elbow pads with ACCS shirt
Impact and ballistic elbow pads in the ACCS system
The ProPad inserts weigh less than 45 g and are seamlessly integrated into the UBACS sleeves via special pockets. The ProPads protect against sharp stones, impacts, cutting objects (including broken glass and barbed wire) and,
for the first time in combat uniforms, provide ballistic protection.
The unique smart, integrated design combined with ultra-light weight ensures maximum comfort, protection and
freedom of movement.
Lightweight, Low profile, Removable, Flexible, Adjustable
Compliant with EN 14404 for puncture and impact resistance Ballistic protection against the threat of low-speed fragments.
The ProPad inserts weigh less than 45 g and are seamlessly integrated into the UBACS sleeves via special pockets. The ProPads protect against sharp stones, impacts, cutting objects (including broken glass and barbed wire) and,
for the first time in combat uniforms, provide ballistic protection.
The unique smart, integrated design combined with ultra-light weight ensures maximum comfort, protection and
freedom of movement.
Lightweight, Low profile, Removable, Flexible, Adjustable
Compliant with EN 14404 for puncture and impact resistance Ballistic protection against the threat of low-speed fragments.
Armor vest Raider
The vest increases a soldier's endurance by up to 30% and protects the spine from protrusions and hernias.
The lightest in its class
The lightest in its class
- Front and back ceramic plates 4 protection level according to NIJ. (6th grade DSTU)
- Frontal, spinal, lateral ballistic protection against fragments
- Quick reset system
- Ventilation system
An anti-gravity system based on the use of a T-shaped spinal belt that relieves the shoulders and spine.
This provides unprecedented advantages:
- increases the warrior's endurance compared to other body armor of a similar class
- prevents protrusion of the spine and spinal hernias during long-term wearing
- allows to avoid spine injuries when jumping from armored vehicles and moving under enemy fire
- Body armor is made of Durabad fabric, which is stronger and lighter than regular Cordura. That's why this vest is the lightest in its class.
- Weight of the vest, including: 2 ceramic plates, 2 pouchs for a grenade, 3 pouchs for 6 cartrige magazines, pouch for a radio, 2 pockets for turnstiles, a pocket for a drinking system, a 17-liter detachable backpack: only 8.5 kg. When using the T-belt system, it feels like 4 kg
- The drinking system is protected by a cover and ergonomically balances the weight of the pouchs with grenades and magazines.
Raider F body armor
with unloading T-belt
with unloading T-belt
Basic plate carrier
with unloading T-belt
with unloading T-belt
Raider M body armor
with unloading T-belt
with unloading T-belt
Specification:
1. Vest ( Molle )
2. Front and back ballistic protection
3. Lateral ballistic protection
4. T-belt
5. Metal-ceramic plates, 4 NIJ
6. Color: green
7. Quick reset system
Optional:
- Shoulder strap for weapons
- Backpack size: small
- Drinking system 3L
- First aid kit (IFAK) with attachment to the T-belt
- Backpack: large on the T-belt
- Bag for storage
1. Vest ( Molle )
2. Front and back ballistic protection
3. Lateral ballistic protection
4. T-belt
5. Metal-ceramic plates, 4 NIJ
6. Color: green
7. Quick reset system
Optional:
- Shoulder strap for weapons
- Backpack size: small
- Drinking system 3L
- First aid kit (IFAK) with attachment to the T-belt
- Backpack: large on the T-belt
- Bag for storage
Specification:
1. Plate carrier ( Molle )
2. Side ballistic protection
3. T-belt
4. Metal-ceramic plates, 4 NIJ
5. Color: green
6. Quick reset system
Optional:
- Shoulder strap for weapons
- Backpack: small
- First aid kit (IFAK) with attachment to the T-belt
- Storage bag
1. Plate carrier ( Molle )
2. Side ballistic protection
3. T-belt
4. Metal-ceramic plates, 4 NIJ
5. Color: green
6. Quick reset system
Optional:
- Shoulder strap for weapons
- Backpack: small
- First aid kit (IFAK) with attachment to the T-belt
- Storage bag
Specification:
1. Vest
2. Front and back ballistic protection
3. Side ballistic protection
4. T-belt
5. Metal-ceramic plates, 4 NIJ
6. Color: green
7. Quick reset system
Optional:
- Shoulder strap for weapons
- Backpack size: small
- 3L drinking system
- Trolley on the T-belt
- First aid kit (IFAK) with attachment to the T-belt
- Backpack: large on T-belt
- Bag for storage
1. Vest
2. Front and back ballistic protection
3. Side ballistic protection
4. T-belt
5. Metal-ceramic plates, 4 NIJ
6. Color: green
7. Quick reset system
Optional:
- Shoulder strap for weapons
- Backpack size: small
- 3L drinking system
- Trolley on the T-belt
- First aid kit (IFAK) with attachment to the T-belt
- Backpack: large on T-belt
- Bag for storage
Basic plate carrier with unloading T-belt
Specification:
1. Plate carrier ( Molle )
2. Side ballistic protection
3. T-belt
4. Metal-ceramic plates, 4 NIJ
5. Color: green
6. Quick reset system
Optional:
- Shoulder strap for weapons
- Backpack: small
- First aid kit (IFAK) with attachment to the T-belt
- Storage bag
1. Plate carrier ( Molle )
2. Side ballistic protection
3. T-belt
4. Metal-ceramic plates, 4 NIJ
5. Color: green
6. Quick reset system
Optional:
- Shoulder strap for weapons
- Backpack: small
- First aid kit (IFAK) with attachment to the T-belt
- Storage bag
Raider F body armor with unloading T-belt
Specification:
1. Vest ( Molle )
2. Front and back ballistic protection
3. Lateral ballistic protection
4. T-belt
5. Metal-ceramic plates, 4 NIJ
6. Color: green
7. Quick reset system
Optional:
- Shoulder strap for weapons
- Backpack size: small
- Drinking system 3L
- First aid kit (IFAK) with attachment to the T-belt
- Backpack: large on the T-belt
- Bag for storage
1. Vest ( Molle )
2. Front and back ballistic protection
3. Lateral ballistic protection
4. T-belt
5. Metal-ceramic plates, 4 NIJ
6. Color: green
7. Quick reset system
Optional:
- Shoulder strap for weapons
- Backpack size: small
- Drinking system 3L
- First aid kit (IFAK) with attachment to the T-belt
- Backpack: large on the T-belt
- Bag for storage
Raider M body armor with unloading T-belt
Specification:
1. Vest
2. Front and back ballistic protection
3. Side ballistic protection
4. T-belt
5. Metal-ceramic plates, 4 NIJ
6. Color: green
7. Quick reset system
Optional:
- Shoulder strap for weapons
- Backpack size: small
- 3L drinking system
- Trolley on the T-belt
- First aid kit (IFAK) with attachment to the T-belt
- Backpack: large on T-belt
- Bag for storage
1. Vest
2. Front and back ballistic protection
3. Side ballistic protection
4. T-belt
5. Metal-ceramic plates, 4 NIJ
6. Color: green
7. Quick reset system
Optional:
- Shoulder strap for weapons
- Backpack size: small
- 3L drinking system
- Trolley on the T-belt
- First aid kit (IFAK) with attachment to the T-belt
- Backpack: large on T-belt
- Bag for storage
Mine resistant footwear
The shoes are characterized by a strong and stable construction, long service life, and do not contain any metal parts.
The shoes are patented.
The shoes are patented.
- 1 Special leather boots with anti-personnel mine protection, withstand the blast of contact mines with a charge of 35 grams of TNT equivalent explosive (model AM-35) and 50 grams (model AM-50). The military boots reduce the explosive energy of a 35 g HE landmine by 99%
- 2 The boots were developed in cooperation with leading Czech ballistic protection specialists. The shoes are equipped with a Drilex/Windtex waterproof membrane that provides complete water resistance while maintaining thermal comfort and moisture wicking ability.
The upper part of the shoe is made of smooth waterproof leather with a thickness of 2.2 to 2.4 mm.
The boot is made of smooth water-repellent leather with a thickness of 1.0 to 1.3 mm, has a closed tongue and a 5-8 mm thick ankle brace Lined on the toe, back and tongue of the shoe with DRILEX - a special non-woven polyamide textile, 100% polyamide of the DRILEX trademark
Has thermoplastic heel protection
Has laces for tying, 4 eyelets and 4 hooks
Shoe height: 27 cm
Color: black
Size range: 39-48
Specification: EN ISO 20347:2004 E WRU P SRC
In order to preserve the properties of the shoe:
Please avoid greasy creams, which can stain the outer layer and impair breathability.
Use the footwear only for its intended purpose.
After each use, clean them and dry them near an indirect heat source.
The user can only replace the laces and the inner insole.
Treat the shoes with a suitable polish.
That in case of thinning of the upper layer, cracks in the sole, the level of protection is reduced and the shoes must be replaced immediately!
The boot is made of smooth water-repellent leather with a thickness of 1.0 to 1.3 mm, has a closed tongue and a 5-8 mm thick ankle brace Lined on the toe, back and tongue of the shoe with DRILEX - a special non-woven polyamide textile, 100% polyamide of the DRILEX trademark
Has thermoplastic heel protection
Has laces for tying, 4 eyelets and 4 hooks
Shoe height: 27 cm
Color: black
Size range: 39-48
Specification: EN ISO 20347:2004 E WRU P SRC
In order to preserve the properties of the shoe:
Please avoid greasy creams, which can stain the outer layer and impair breathability.
Use the footwear only for its intended purpose.
After each use, clean them and dry them near an indirect heat source.
The user can only replace the laces and the inner insole.
Treat the shoes with a suitable polish.
That in case of thinning of the upper layer, cracks in the sole, the level of protection is reduced and the shoes must be replaced immediately!
When testing the boots, the following are carried out:
The experimental assembly is shown in the figure below. A KISTLER pressure transducer, model 6215, is used to measure the pressure coming through the sole to the wearer's foot. The apparatus for the experiment should be able to accommodate a suitable weight of 30 to 75 kilograms.
The space between the test charge and the shoe is filled with fine dry sand inside a 100 mm diameter ring of hard paper or plastic 3 cm high.
The test charge used is nitrohexane with a mass of 30 gms for AM-L, 35 gms for AM-35 and 50 gms for AM-50, which will be initiated by an electric detonator from below in a vertical position.
For the test, 3 boots are used and the test result will be the arithmetic mean of the three measurements. The result should be a pressure of less than 1% entering the boots.
The heel of the mine protection boot is resistant to particles with a velocity of at least 450 m/s. Mine protection boots will provide the required protection in accordance with STANAG 2920 V50.
- physical testing
- explosive testing
The experimental assembly is shown in the figure below. A KISTLER pressure transducer, model 6215, is used to measure the pressure coming through the sole to the wearer's foot. The apparatus for the experiment should be able to accommodate a suitable weight of 30 to 75 kilograms.
The space between the test charge and the shoe is filled with fine dry sand inside a 100 mm diameter ring of hard paper or plastic 3 cm high.
The test charge used is nitrohexane with a mass of 30 gms for AM-L, 35 gms for AM-35 and 50 gms for AM-50, which will be initiated by an electric detonator from below in a vertical position.
For the test, 3 boots are used and the test result will be the arithmetic mean of the three measurements. The result should be a pressure of less than 1% entering the boots.
The heel of the mine protection boot is resistant to particles with a velocity of at least 450 m/s. Mine protection boots will provide the required protection in accordance with STANAG 2920 V50.
Mine Resistant Footwear - model (mine resistant) offers a three-layer protection system:
1) "Intelligent" multilayer armored outsole.
The outsole contains special multilayer structures. When the pressure (explosive energy) reaches the outsole,
the following happens:
Some parts reflect the energy back.
Part of the energy is used up in the programmed delamination and destruction of the special high-strength layers.
Only a small portion of the energy passes through the armor and reaches the inner layer of the shoe. The maximum
pressure that passes through the shoe is usually less than 1% of the initial energy of the mine explosion - 35 g TNT.
The shoe reduces the explosive effect by 99% (35 g TNT mine).
2) Internal armored insole
Inside the shoe there is a special insole that reduces the impact of explosion pressure on the human body.
3) Anti-perforation layer.
The special "smart" design of the outsole provides the following protection during an explosion
protection against fragments, which is 2.5 times stronger than required by European standards for safety shoes, while maintaining flexibility, thereby contributing to wearing comfort.
Other benefits
No part of the shoe contains any metal parts. This ensures that the shoe does not give false signals to metal detectors. Special construction with an anatomical design and antibacterial inner insole that helps absorb energy while walking,
reduces stress on the joints and relieves fatigue.
The design of The Blast Protective model includes an intelligent metal-free outsole system and an anti-perforation system that provides synergistic multi-level protection and additional benefits. The boots are designed for full-day wear. There are models for 10-35-50 grams of TNT.
The outsole contains special multilayer structures. When the pressure (explosive energy) reaches the outsole,
the following happens:
Some parts reflect the energy back.
Part of the energy is used up in the programmed delamination and destruction of the special high-strength layers.
Only a small portion of the energy passes through the armor and reaches the inner layer of the shoe. The maximum
pressure that passes through the shoe is usually less than 1% of the initial energy of the mine explosion - 35 g TNT.
The shoe reduces the explosive effect by 99% (35 g TNT mine).
2) Internal armored insole
Inside the shoe there is a special insole that reduces the impact of explosion pressure on the human body.
3) Anti-perforation layer.
The special "smart" design of the outsole provides the following protection during an explosion
protection against fragments, which is 2.5 times stronger than required by European standards for safety shoes, while maintaining flexibility, thereby contributing to wearing comfort.
Other benefits
No part of the shoe contains any metal parts. This ensures that the shoe does not give false signals to metal detectors. Special construction with an anatomical design and antibacterial inner insole that helps absorb energy while walking,
reduces stress on the joints and relieves fatigue.
The design of The Blast Protective model includes an intelligent metal-free outsole system and an anti-perforation system that provides synergistic multi-level protection and additional benefits. The boots are designed for full-day wear. There are models for 10-35-50 grams of TNT.
Mask
Mask
CHEMBAYO is specially designed for use in the following areas:
Defense and military
Law enforcement agencies
Emergency services
This respiratory protective device is designed for evacuation in case of an emergency involving weaponized chemical and biological agents. The CHEMBAYO mask provides users with short-term respiratory protection against low concentrations of various toxins, with an emphasis on protection against nerve and blood agents, combined with HEPA filtration capabilities (P3) that filter out particles and aerosols, greatly reducing respiratory exposure.
Defense and military
Law enforcement agencies
Emergency services
This respiratory protective device is designed for evacuation in case of an emergency involving weaponized chemical and biological agents. The CHEMBAYO mask provides users with short-term respiratory protection against low concentrations of various toxins, with an emphasis on protection against nerve and blood agents, combined with HEPA filtration capabilities (P3) that filter out particles and aerosols, greatly reducing respiratory exposure.
- Pocket-size.
- No adjustment straps.
- One size fits all.
- Strong, fire-resistant, elastic rubber hood, protects the entire head and seals comfortably at the neck.
- Large visor, made of flame-retardant transparent film, allows a wide field of view.
- High-efficiency, electrostatic particle filter, with extremely low pressure-drop to allow easy breathing.
- Layers of activated charcoal with special impregnation to absorb toxic gases.
- A unique breathing device (patent pending) enables rapid exhalation and improves the physiological conditions for the user, preventing built-up of heat or vapour inside the mask.
Hood:
Visor:
ETFE film – a copolymer of Polytetrafluoroethylene with Ethylene monomer.
- Special Polychloroprene Latex Compound
- Elongation at break: > 700%
- Tensile strength: > 150 kg/cm²
- Temperature resistance: 200°C
- Fire-resistant to the requirements of NFPA 701
Visor:
ETFE film – a copolymer of Polytetrafluoroethylene with Ethylene monomer.
- Tensile strength: 50N/mm²
- Elongation at break: 450%
- Tear resistance: 500 N/mm
- Temperature resistance: 150°C
- Flame retardant : UL 94 V-O
- Light transmission: > 95%
Multi-Layer filter includes the following:
- External polyester screen, fire resistant to the requirements of NFPA 701
- Electrostatic + melt blown combination high efficiency particle filter (HEPA)
- Layers of activated charcoal cloth with a special impregnation against acid gases
- Soft inner pad of non-woven material
PSA OXYGEN PLANT
PSA OXYGEN PLANT
Meets all WHO requerenents lifetime up to 25 years, subject to regular maintenance
Capacity: 150/280/420/550/610 LPM 93-95% oxygen at 4,8 barg
Weight 6.500 – 9.500 kg
Capacity: 150/280/420/550/610 LPM 93-95% oxygen at 4,8 barg
Weight 6.500 – 9.500 kg
- Energy recuperation available 85%01
- Remote control available02
- Cyllinder filing available03
Features:
- Mobility and plug&play
- High quality equipment: do not need to change Zeolite
- Futuristic outside desing
- Rooftop air condition and heating equipment
- Modern interior decoration
Safe and fire protected
All weather and 24/7
Neutral to the environment, reduced carbon emissions
Operation temperature +50C up to -30C
Insulation and moisture resistant design
Fully digital and automated
Heat and cold energy saving +65%
Contacts:
Phone: +48 511 131 594; +38 096 640 50 55
E-mail: info@imex-company.com
Contact the director: ceo@imex-company.com
E-mail: info@imex-company.com
Contact the director: ceo@imex-company.com
IMEX COMPANY Sp. z o.o.
Warsaw 00-052, St. Swietokrzyska 18, office 316
Warsaw 00-052, St. Swietokrzyska 18, office 316
Thank you for contacting IMEX COMPANY
Produkty oferowane do sprzedaży na tej stronie są opracowywane przy użyciu unikalnych opatentowanych technologii oraz indywidualnych technologii projektowych firmy producenckiej.
Każda próba skopiowania lub naruszenia w inny sposób praw firmy producenckiej (upoważnionego przedstawiciela) spowoduje skutki prawne, w tym odpowiedzialność karną.
Naruszeniem praw firmy producenckiej (upoważnionego przedstawiciela) będzie uważana każda próba kopiowania, imitacji produktów oferowanych na sprzedaż, ich elementów, unikalnych rozwiązań projektowych lub cech.
Firma producencka (upoważniony przedstawiciel) zastrzega sobie prawo do zgłaszania roszczeń majątkowych przeciwko naruszycielowi, które mogą wynosić 25 000 USD.
Każda próba skopiowania lub naruszenia w inny sposób praw firmy producenckiej (upoważnionego przedstawiciela) spowoduje skutki prawne, w tym odpowiedzialność karną.
Naruszeniem praw firmy producenckiej (upoważnionego przedstawiciela) będzie uważana każda próba kopiowania, imitacji produktów oferowanych na sprzedaż, ich elementów, unikalnych rozwiązań projektowych lub cech.
Firma producencka (upoważniony przedstawiciel) zastrzega sobie prawo do zgłaszania roszczeń majątkowych przeciwko naruszycielowi, które mogą wynosić 25 000 USD.